- Manuals
- Brands
- HUANUO Manuals
- HNDS8
- Instruction manual
Monitors desk mount
Hide thumbs Also See for HNDS8:
- Installation instructions manual (12 pages) ,
- Instruction manual (15 pages)
1
2
3
4
5
6
7
8
9
10
11
12
13
Table Of Contents 14
-
- Contents
- Table of Contents
- Bookmarks
Table of Contents
-
Safety Information
- Weight Restrictions
-
Check the VESA Pattern of Monitor before You Begin the Installation
- Product Features
- Tension Adjustment
-
Tools Needed
-
Supplied Parts and Hardware
-
For Clamp Mounting
-
Install the C-Clamp
- Step 1 Install the Base
-
For Grommet Mounting
-
Install the Arms
-
Attach Monitors to the Arms
- Adjust Gas Spring Tension
-
Rotation Restriction
-
Step 6 Tilt Adjustment
-
Step 7 Rotation Adjustment
-
Route Cables Along the Arms
Advertisem*nt
Quick Links
- 1 Weight Restrictions
- 2 Product Features
- 3 Tension Adjustment
- 4 Supplied Parts and Hardware
- 5 Step 1 Install the Base
- 6 For Clamp Mounting
- 7 Adjust Gas Spring Tension
- 8 Step 6 Tilt Adjustment
- Download this manual
Table ofContents
Advertisem*nt
Table of Contents
Related Manuals for HUANUO HNDS8
-
Desk monitor arm (15 pages)
-
(12 pages)
-
Gas spring dual and single monitor mount (4 pages)
-
Gas spring dual and single monitor mount (4 pages)
-
Desk monitor arm (32 pages)
-
Monitor desk mount (12 pages)
-
Monitor desk mount (16 pages)
-
Gas spring monitor mount trouble-shooting (5 pages)
-
Full motion desk mount (12 pages)
-
Monitor desk mount (11 pages)
-
Monitor arm reinforcement plate (2 pages)
-
Single arm monitor desk mount (12 pages)
-
Monitor desk mount (12 pages)
-
Monitor stand (6 pages)
-
(10 pages)
-
Wall monitor arm (64 pages)
Summary of Contents for HUANUO HNDS8
- Page 2 IMPORTANT SAFETY INFORMATION Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at support@huanuoav.com. CAUTION: Avoid potential personal injuries and property damage! • Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
- Page 3 Product Features C-Clamp Mounting Grommet Mounting...
- Page 4 TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION Do not adjust tension without monitor 1. Ensure monitor has been attached to the mount. 2. Read your monitor box or manual to find out monitor net weight. 3. Ensure the net weight of monitor (including accessories) is between 4.4~19.8 Ibs (2-9 kg).
- Page 5 Tools Needed (Not lncluded) Screwdriver Supplied Parts and Hardware Warning :This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our customer service at support@huanuoav.com.
- Page 6 Supplied Parts and Hardware for Step 2 Arm X2 Cable Clip X2 5/32 in.(4mm) Allen Key Supplied Parts and Hardware for Step 3 Bolt (A) Bolt (B-1) Spacer (B-2) M4x12mm (8pcs) M4x16mm (8pcs) 5mm (8pcs) Supplied Hardware for Step 4 and Step 6 13/64 in.(5mm) Allen Key Supplied Parts and Hardware for Step 8...
- Page 7 Step 1 Install the Base A. For Clamp Mounting A-1 Install the C-Clamp Connect part [X] to pole Warning: assembly [03] Ensure bolts are secured firmly. Detach the c-clamp entirely ① 5/32 in. ② (4mm) Connect part [Y] to part [X] according to the thickness of the desktop The first choice The second choice Secure the base to the desktop...
- Page 8 B. For Grommet Mounting 1 Install the grommet bolt Warning: Ensure bolts are secured firmly. Secure the base to desktop using locking plate [E] and butterfly nut [D] Warning: Ensure bolts are secured firmly.
- Page 9 Step 2 Install the Arms Slide the cable clip [05] to the pole assembly [03] Slide arm [01] to the pole assembly [03] Secure the arm [01] to the pole assembly [03] by tightening the preassemble bolts on the arms [01] Ensure bolts are secured firmly.
- Page 10 Step 3 Attach Monitors to the Arms 3-1 Choose Proper bolts 3-2 Install Monitors to the Arms Flat back monitor 0.1-0.2in.(3-5mm) spacing left Screwdriver [Not Included] Round back monitor The tension is preset at 8.8~11 Ibs(4-5kg). After hanging the monitor to the mount,please release the monitor slowly to prevent it from falling suddenly.
- Page 11 13/64 in. (5mm) (1 rotation ≈ 1 lb) Step 5 Rotation Restriction Proper usage directions Non-proper usage directions...
- Page 12 Step 6 Tilt Adjustment 13/64 in. (5mm) “+” Clockwise: Tighten “-” Counter-clockwise: Loosen Situation 1: If the monitor can stay at the desired tilt angle by itself, no adjustment needed. Situation 2: If the monitor can not stay at the desired tilt angle by itself, turn the bolts clockwise or counter-clockwise as shown until the monitor can stay at the desired tilt angle by itself.
- Page 13 Step 8 Route Cables along the Arms Screwdriver [Not Included] Secure the Cable Cover [04] to the arm [01] by tightening the bolts [G] using screwdriver Loosen the preassembled bolts [S] on the Route the cables into the cable guide and arm [01] to detach the cable guide from the secure the cable guide by tightening the arm [01], and keep the bolt for the use in...
